CarderPlanet
Professional
- Messages
- 2,552
- Reaction score
- 698
- Points
- 83
The information is provided for informational purposes only. The actions described below are illegal. The administration does not call or promote anything!
In this lesson I will show you how to convert the signal mp - 371 into a trauma. Let `s start? To get started, go and order yourself mp - 371
Can be found in a store that sells pneumatics, etc.
(Order everything for a drop, in no case for yourself).
So we saved up some money, ordered this miracle, took it from the post office
These tubes can be purchased at:
http://forum.guns.ru/forummessage/302/1604780.html (the author advises here, but I myself did not buy, I cannot advise myself)
Important: Our mp has 371 holes in the earring initially 11mm, which means that we need a tube that has a Landing diameter of 11mm.
If the PIPE is 13 MM LANDING, then it simply will not fit into our earring, and then in order for it to fit we will need to:
1) First knock out the blank and the chamber
2) Hammer a chopik made of wood + foil into the earring so that the snot does not flow inside
3) Weld the earring
4) And only then ]unfold the earring by 13 mm
5) You need to unfold at low speeds with a drill with drills 11 later than 12 and finish
12.8 - 12.9 (it is better not to save on drills)
Attention In no case should you first unfold the earring and then boil it! If you do this, then you will simply burn the earring and fucking fail.
So in order for us not to fuck our brains so much, we buy a tube that has a Rim diameter of 11mm.
So we saved up some money, ordered a pipe, took it from the post office. Now, in order to put our pipe on, we need to get rid of the standard blank and chamber.
Method 1
Take a 2 mm drill bit and drill out pins 1 and 2 and knock out the blank and the chamber!
Method 2
In stock 371, into the hole where the chamber you need to insert a piece of nail with a head, into the cartridge (metal) sprinkle powder. and shoot until the pipe blows. everything is held on the nozzle there. After a couple of good bangs, the pipe should fly out.
Method 3 (Personally, I used this method. (Author)
We clamp the barrel into the pieces and hammer on the blanks with a hammer, as if you hammer it in, and with a stalemate, as the pins will come, you just need to unscrew it with flat pliers. With the same pipe, we knock out the chamber very quickly and simply. I didn't even have to drill anything.
As a result, it should look like this:
Now we insert our pipe into the earring (By the way, this is not an earring! The earring is from TT. This is a stand !!! Learn materiel.) Well, don't give a fuck.
We weld the earring and process
We take a boron machine and remove this pin, it does not allow installing the shutter on other frames. So, for example, you cannot put this shutter on the frame of the 654th. Who does not have a boron machine, take a round file and put it in a drill, here is a kind of drill for you)))
Drank on the beard, we brew it with a semiautomatic device and process
The whole gun is ready!
It remains only to replace the store.
Initially, there is a store that is similar to the real one, with a metal feeder. But it has one joint. A strip of metal is welded along the left wall at the back. So that it was impossible to insert live or traumatic cartridges. Why it was necessary to do this, I still did not understand, because stores from injury are sold freely for 500+ rubles in guns.
You can also change the bakelite handle, for a more reliable fiberglass handle, well, I did not do that.
In this lesson I will show you how to convert the signal mp - 371 into a trauma. Let `s start? To get started, go and order yourself mp - 371
Can be found in a store that sells pneumatics, etc.
(Order everything for a drop, in no case for yourself).
So we saved up some money, ordered this miracle, took it from the post office
These tubes can be purchased at:
http://forum.guns.ru/forummessage/302/1604780.html (the author advises here, but I myself did not buy, I cannot advise myself)
Important: Our mp has 371 holes in the earring initially 11mm, which means that we need a tube that has a Landing diameter of 11mm.
If the PIPE is 13 MM LANDING, then it simply will not fit into our earring, and then in order for it to fit we will need to:
1) First knock out the blank and the chamber
2) Hammer a chopik made of wood + foil into the earring so that the snot does not flow inside
3) Weld the earring
4) And only then ]unfold the earring by 13 mm
5) You need to unfold at low speeds with a drill with drills 11 later than 12 and finish
12.8 - 12.9 (it is better not to save on drills)
Attention In no case should you first unfold the earring and then boil it! If you do this, then you will simply burn the earring and fucking fail.
So in order for us not to fuck our brains so much, we buy a tube that has a Rim diameter of 11mm.
So we saved up some money, ordered a pipe, took it from the post office. Now, in order to put our pipe on, we need to get rid of the standard blank and chamber.
Method 1
Take a 2 mm drill bit and drill out pins 1 and 2 and knock out the blank and the chamber!
Method 2
In stock 371, into the hole where the chamber you need to insert a piece of nail with a head, into the cartridge (metal) sprinkle powder. and shoot until the pipe blows. everything is held on the nozzle there. After a couple of good bangs, the pipe should fly out.
Method 3 (Personally, I used this method. (Author)
We clamp the barrel into the pieces and hammer on the blanks with a hammer, as if you hammer it in, and with a stalemate, as the pins will come, you just need to unscrew it with flat pliers. With the same pipe, we knock out the chamber very quickly and simply. I didn't even have to drill anything.
As a result, it should look like this:
Now we insert our pipe into the earring (By the way, this is not an earring! The earring is from TT. This is a stand !!! Learn materiel.) Well, don't give a fuck.
We weld the earring and process
We take a boron machine and remove this pin, it does not allow installing the shutter on other frames. So, for example, you cannot put this shutter on the frame of the 654th. Who does not have a boron machine, take a round file and put it in a drill, here is a kind of drill for you)))
Drank on the beard, we brew it with a semiautomatic device and process
The whole gun is ready!
It remains only to replace the store.
Initially, there is a store that is similar to the real one, with a metal feeder. But it has one joint. A strip of metal is welded along the left wall at the back. So that it was impossible to insert live or traumatic cartridges. Why it was necessary to do this, I still did not understand, because stores from injury are sold freely for 500+ rubles in guns.
You can also change the bakelite handle, for a more reliable fiberglass handle, well, I did not do that.
