HOW TO CLONE IN 2024
Required Equipment:
1. Omnikey (for writing the chip data on the card)
2. Magnetic Stripe Card Reader (I recommend the Msr605x)
3. Computer/Laptop
4. Blank card (J2a040 and Unfused)
All the equipment listed above can be found online, like at Amazon for example.
5. Track data. Which should like this for track1:
4300232765346056^SURNAME/NAME^ 31052500837291034845
The corresponding track2 should look like this:
4300232765346056= 31052500837291034845
6. Software (MSRX, ARQC Gen, Cardpeek, X2 emv (the newer the best), Jcop English and ATR TOOL 2_0)
If you're sure you have all the correct required equipment, we can start swiping.
Instructions:
1. Start up your computer/laptop
2. Make sure you have all the equipment you need
3. Now run the program MSRX as administrator and plug in your card reader, make sure the program says, "Device Online!". This gives you confirmation of your card reader being correctly connected. Enter the track data you have into the "Track1" & "Track2" boxes, now select the option "Write" and swipe your blank card through your device. To double check if the data was written correctly select the option "Read" and check if everything is according. If all is good close MSRX and unplug your card reader, you have successfully written the data on the magstripe of the card.
4. Plug in your Omnikey and open the program Jcop English. Select the option "Delete jcop files" to make sure there is no card data. After that restart Jcop English, and enter your track2 data into the "Track number:" tab, it should automatically detect which card script you have (Visa credit, Master credit etc.). Now select the option "Format Jcop chip" and wait for the program to display "JCOP CHIP FORMATTED WITH SUCCES", after that select "Save Track jcop chip" and wait for your Omnikey light to stop blinking.
Close Jcop English, don't disconnect your omnikey you're still going to need it for the following steps.
5. Next step, open ATR Tool 2.0. Select your omnikey in the tab "Reader" and select "JCOP J2A040" in the tab "JavaCard". After that select the bank corresponding to your track data, if you don't know what bank it is for you search up Bin Checker online. Here you can look up all the info about your bin number which is the first six numbers of your track number or credit card number, for example: 4300232765346056. The first 6 numbers are 430023, so that's the bin number of that specific card. Select the tab "Default" and choose the bank that's corresponding to the data that you're using. If all is good select "Set" and close ATR Tool 2.0.
6. Now for the most difficult program, X2. Open X2 and select "EMV" at the top. Enter your track 2 into the tab "Track 2" and enter the cardholders name into tab "cardholders name". This can be found in track 1 number like this SURNAME/NAME, enter this the same way into X2. After that enter the application label into the tab "Application Label (10 letters)". This label can also be found in Bin checker and should look like this: VISADEBIT, VISACREDIT, AMEXCREDIT etc. Select the card type for your info under the text "CREDIT", you should have the options: MASTERCARD, VISA and AMEX.
Under the text "WRITTER" select the option "Omnikey".
7 . Now stay on EMV don't close anything. Select the box "Change Data" next to the "Expiration Data" and enter the expiration date into the tab. The date are the first six numbers after the credit card number so for example our date is 310525 or in other words May 31st, 2025, 4300232765346056= 31052500837291034845. If that is
entered, enter the AID into "AID" tab, which is basically data that recognizes which bank is issued. For now, I will use 31010 as the standard aid for visa. Enter the pin into the "Pin" tab, the pin should be given with the track information. Do the same for the tabs "Country Code" and "Currency". For both these tabs I will use 0840 which is the code for both the United States and USD. Now click "Credit" at the bottom of the tab and for it to give the pop-up "Completed job!". After all that is done, select the "IST LOAD" tab at the top.
Here select, "Open..." this will let you select an IST. file out of your files. Select the IST. file corresponding to your bin number, After that, enter track2 into the "Track 2" tab and do the same for the cardholder's name, application label, country code and currency. It's just a matter of copy & pasting.
9. Don't close X2 yet, open ARQC Gen. Enter your card number into the "Pan (Card number)" tab and select the country code and currency code corresponding to your information into the "Country Code" and "Currency Code" lists. Enter the expiration date like you did before in step 7 into the tab "Date (YYMMDD)" and select "Generate
ARQC". There now should be a combination of numbers and letters in the "ARQC" tab, copy & paste this into "ARQC 1" tab in the X2 program. Double check if all is gone correctly. If all is good, select "Burn" and wait for the "Completed Job!" pop-up. You're now done with X2 and ARQC Gen, you have successfully written the chip of the card. Exit both programs.
10. (Optional but recommended) Open Cardpeek and select "EMV" on the option "Analyzer" at the top. The program will now scan the card from your omnikey device. A couple pop-ups might come up, select "Yes" for all. The loading process should take around 5 minutes, if this is not the case something might have gone wrong. After the
loading has been done there should be a lot of data showing on your cardpeek program. I recommend going through it globally and picking out the important parts like "Usable at atm" to see if everything is okay. Once you're done with that and all is good, you can exit Cardpeek. YOU have successfully swiped a card!
IMPORTANT STUFF:
- X2 EMV 2021 AND LOWER VERSIONS MAY NOT WORK I RECOMMEND TRYING X2 EMV 2023 OR X2 EMV 2024
(A PLUG OF THIS VERSIONS http://duysanjqxo4svh35yqkxxe5r54z2xc5tjf6r3ichxd3m2rwcgabf44ad.onion/user/CardingGOV guaranteed refund)
- MAKE SURE YOU ORDER J2A040 FROM A VENDOR WITH GOOD FEEDBACK
(I RECOMMEND AMAZON)
- TO CLONE A DUMP YOU NEED IST.IST NEEDS A PHYSICAL CARD OF THE BANK OF THE DUMP TO BE GENERATED
- video tutorial:
