Greetings, this topic shows how to assemble an audio skimmer in 10 minutes, without spending much.
This method is known to everyone, but still, let's take a closer look.
We need: a Chinese spy pen, a tape recorder head, a phone battery (860mah is enough), 2 different wiring flowers, insulating tape and a soldering iron.
Where do we start?
Of course, with the choice of a Chinese spy pen
Pens come with built-in memory (2-16GB) or with a slot for a micro-sd flash drive, this stuff is easy to use and card in Chinese shops. It is better to make several models of pens from different Chinese shops.
And so, we take the handle, unscrew the bottom of the handle where the rod is, we see the input for charging (it can be of 2 types (input for the wire as on the players, Nokia 6300, etc.) or just USB
I came across USB. Remove the pen body, only the board remains in front of us.
Here is a photo of this board:
There are only 2 buttons on it: Above-on / off, in the middle-reset.
And also 2 lights: yellow-charging / standby, blue-video recording.
It is necessary to replace the battery, otherwise the skim will not work for long, we remove the old one and put a new battery, it will be located at the top of the
muzzle.Before soldering the head, we need to increase the wires that will connect the head to the board, we solder the old ones (they are in the photo: red and black ), we solder the wiring about 4 cm so that there is a small margin and the head is in the transparent as expected.
we solder the head to the wires - it remains only to install and pour everything correctly. The camera is installed at an angle (here you will need to measure at the atm whether it is standing correctly)
The total will turn out (photo taken from the Internet):
These audio guts are suitable only for the opteva dib) now many models of this company are equipped with sensors for skimmers. How to check if there is such a sensor?
And everything is very simple, in the dark, we sculpt a nail on the scotch tape on the card collector and wait) if within 30 minutes it has not gone off and no one has arrived, then this anti-skimming system is not installed on this ATM.
Interference caused by ATM is also possible, shield your devices).
P.S. Before installing the guts, glue the muzzle from the inside again (no matter how the sellers assure you of the strength of the muzzles), otherwise a little misunderstanding may happen.
P.S.S. We do not work on the hands personally, I will beat the ass.
Author of this article does not bear any responsibility for your actions. Everything that you do - you do at your own peril and risk.
All the best, may labor carders forgive me.
This method is known to everyone, but still, let's take a closer look.
We need: a Chinese spy pen, a tape recorder head, a phone battery (860mah is enough), 2 different wiring flowers, insulating tape and a soldering iron.
Where do we start?
Of course, with the choice of a Chinese spy pen
Pens come with built-in memory (2-16GB) or with a slot for a micro-sd flash drive, this stuff is easy to use and card in Chinese shops. It is better to make several models of pens from different Chinese shops.
And so, we take the handle, unscrew the bottom of the handle where the rod is, we see the input for charging (it can be of 2 types (input for the wire as on the players, Nokia 6300, etc.) or just USB
I came across USB. Remove the pen body, only the board remains in front of us.
Here is a photo of this board:
There are only 2 buttons on it: Above-on / off, in the middle-reset.
And also 2 lights: yellow-charging / standby, blue-video recording.
It is necessary to replace the battery, otherwise the skim will not work for long, we remove the old one and put a new battery, it will be located at the top of the
muzzle.Before soldering the head, we need to increase the wires that will connect the head to the board, we solder the old ones (they are in the photo: red and black ), we solder the wiring about 4 cm so that there is a small margin and the head is in the transparent as expected.
we solder the head to the wires - it remains only to install and pour everything correctly. The camera is installed at an angle (here you will need to measure at the atm whether it is standing correctly)
The total will turn out (photo taken from the Internet):
These audio guts are suitable only for the opteva dib) now many models of this company are equipped with sensors for skimmers. How to check if there is such a sensor?
And everything is very simple, in the dark, we sculpt a nail on the scotch tape on the card collector and wait) if within 30 minutes it has not gone off and no one has arrived, then this anti-skimming system is not installed on this ATM.
Interference caused by ATM is also possible, shield your devices).
P.S. Before installing the guts, glue the muzzle from the inside again (no matter how the sellers assure you of the strength of the muzzles), otherwise a little misunderstanding may happen.
P.S.S. We do not work on the hands personally, I will beat the ass.
Author of this article does not bear any responsibility for your actions. Everything that you do - you do at your own peril and risk.
All the best, may labor carders forgive me.
